kwikzuloo.blogg.se

N track studio ex registration code
N track studio ex registration code






n track studio ex registration code

All TesiraFORTÉ AVB processors marked Rev.

  • Added support for updated components in TesiraFORTÉ AVB processors.
  • B TesiraFORTE AI models could be slow to respond in certain layouts that use a lot of DSP resources.

    n track studio ex registration code

    B would not start on boot and require a power cycle.

  • Resolved rare issue where TeisraFORTÈ Rev.
  • B could show “Internal SW Error(m)” on boot.
  • Resolved rare issue where TesiraFORTÈ Rev.
  • Resolved rare issue where TesiraFORTÈ X could show wrong MAC addresses on wrong ports.
  • Resolved issue where multiple Parlè Mics connected to a TesiraCONNECT result in mic capsule fault conditions.
  • Resolved issue where Dante flows could lose channel names due to reboot, layout change, or network change.
  • Resolved issue where Dante audio could have crackling when using TesiraCONNECT TC-5D as Dante media master.
  • Resolved issue where Dante input audio could click every half-second.
  • Resolved issue where TesiraFORTÈ X could show “Dante card failed to sync clock to backplane” when AVB is set as the clock master.
  • Resolved issue where factory reset would result in Dante card not resetting to Tesira default hostname.
  • Updates Dante implementations to Dante version 4.2.3.x.
  • Added minor fault message for when NTP is configured but cannot get time from the server.
  • Support for pre-existing processors is maintained in this firmware version. B must use Tesira firmware 4.2.3 or later. All TesiraFORTÉ DAN processors marked Rev.
  • Added support for updated components in TesiraFORTÉ DAN (Rev.
  • Released April 2022, Firmware-only release, aligned with software release 4.2.2
  • Resolved issue in which Tesira software could lose its control connection resulting in devices hanging and rebooting.
  • Resolved issue with TesiraFORTE X models not receiving AES67 streams.
  • Resolved issue where Tesira EX-UBTs connected across multiple TesiraConnects would have intermittent AVB stream drops.
  • Resolved issue where VoIP log would not clear a “Not Registered” fault.
  • Resolved issue on TesiraFORTE X where the web UI would show the wrong IP Gateway.
  • Resolved issue in which DHCP lease time not shown in TTP response for network info.
  • Resolved issue where ethernet traffic could show up on the wrong ports on TesiraFORTE X.
  • Resolved issue where devices running Tesira 4.0 and newer could lose network connectivity after DHCP lease renewal.
  • Resolved issue where Tesira XEL Amplifiers would drop AVB Streams or become undiscoverable after reboot.
  • TesiraFORTE DAN models would only pass 2 or 4 channels of Dante audio.

    n track studio ex registration code

  • Resolved issue where Tesira Software would report 100% DSP utilization on Server IO DSP-2 card when it was not using 100%.
  • Resolved issue where changing the channel count on a Parlé Processing block could cause Tesira Software to restart.
  • Resolved issue where Tesira Software could crash when a VoIP X block was selected in “Server Only” mode.
  • Added support for Rev B models of TesiraFORTE X and TesiraCONNECT TC-5 and TC-5D.
  • Added ability to set IP Settings on Media Interface on NPX Paging devices.
  • Added Dante Fault reporting on all TesiraFORTE X and TesiraFORTE DAN models.
  • Added new entries in the processing library for the new Desono EX-S6, EX-S8, EX-S10, and EX-S10SUB speakers.
  • Resolved issue where a TesiraFORTE X may transmit a RSTP packet during boot even though RSTP is disabled.
  • Resolved issue with incorrect channel routing in TesiraXEL after running locate.
  • Resolved issue where VoIP X transmit packets with high jitter cause audio drops.
  • Resolved issue of compilation errors after adding a VoIP X block.
  • Added USB connect and disconnect messages to event logs for all products.
  • The event logs download now includes a new TTP (Tesira Text Protocol) log that provides information to assist troubleshooting control automation behavior.
  • NPX paging station LCD now displays “Ready for configuration …” when unconfigured.
  • NPX in AVB mode no longer requires dynamic VLANS (MVRP).
  • Added support for page code labels and preamble/recorded message labels in the following languages:.
  • NPX media type can now be changed without having to delete all page and zone control elements.
  • Added custom message slot protection option to prevent users from overwriting important messages when recording local messages.
  • NPX Paging Stations on separated networks in AVB mode can now be setup from a PC with a single network inteface.
  • Added page active logic output from the Paging Zone block to signal when a page is active in a zone.
  • The update process is detailed here: Normal Tesira firmware update procedure. This article provides details of Tesira Software and Firmware revisions as well as Biamp Canvas revision notes.








    N track studio ex registration code